Page 22 – Vivax-Metrotech

vLoc-9800 Receiver

November 26, 2017November 27, 2018

The vLoc-9800 is the updated version of the popular legacy 9860XT and 9890XT locators. With updated modern technology, we have combined the best of both legacy locators into the vLoc9800. The vLoc-9800 provides simplicity and fast performance with distance sensitive Left/Right Guidance™ and full automatic gain with the option to switch to manual....

Loc-5STx 5-Watt Transmitter and Loc-5DTx 5-Watt Dual Output Transmitter

November 17, 2017December 4, 2019

The Loc-5STx broadband transmitter has selectable induction frequencies from 8kHz to 200kHz and direct-connect frequencies from 512Hz to 200kHz. SD (Signal Direction), fault find and true resistance measurement up to 1 Mohm are all standard. The two inch by one-inch back-lit dot matrix display shows output current, connection type, volts, resistance, frequency, volume,...

Loc-10Tx 10-Watt Series Transmitters

October 17, 2017December 17, 2018

The Loc-10Tx broadband transmitter has selectable induction frequencies from 8kHz to 200kHz and direct-connect frequencies from 512Hz to 200kHz. SD (Signal Direction), fault find and true resistance measurement up to 1 Mohm are all standard. The two inch by one-inch backlit dot matrix display shows output current, connection type, volts, resistance, frequency, volume,...

vLocML2+ Receiver

September 21, 2017August 21, 2019

The vLocML2+ Receiver is an extended version of the popular vLocPro2 with the addition of the ability to locate buried electronic markers. The vLocML2+ comes with passive modes of Power and Radio, a range of preloaded active frequencies from 50Hz to 200kHz, Sonde Mode, SD (Signal Direction) mode and Electronic Marker modes. The vLocML2+ has an internal memory to...

vLocDM2 Receiver

September 20, 2017April 5, 2020

The vLocDM2 (Defect Mapper) uses the latest locating and signal processing techniques to plot the current gradient of an industry standard low frequency (3Hz or 4Hz) profiling current. The current is applied at CP stations, so the disruption of the pipeline can be minimized. The non-intrusive measuring device, the vLocDM2 receiver, takes measurements along the...

vLocPro2 (VLP2) Receiver

September 19, 2017December 30, 2020

The vLocPro2 (VLP2) utility locator receiver was designed to meet the tough requirements of the modern world. With more and more utilities being buried each day and also abandoned each day, it truly is a jungle beneath the ground. Today’s locator must not only trace the path of a buried utility, it must assure the...

Spar 300

September 18, 2017November 30, 2022

The Spar 300 family represents a comprehensive approach to surveying and mapping underground utilities. It is fully integrated with the Trimble® Access surveying environment, and operates seamlessly with Trimble® GNSS receivers, may be used with Trimble® Total Stations and is available from many Trimble® dealers. The Spar employs a set of magnetic field sensors...

vLoc2 Accessory A-Frame

August 18, 2017June 26, 2023

The vLoc2 Series Accessory A-Frame accessory is used to detect ground faults on pipes and cables. In the case of pipes, the faults consist of coating defects. In the case of cables, faults are usually caused by insulation damage allowing the metallic sheath (or internal conductor) to become in contact with the ground. It is...

The new VM-510FFL Standalone A-frame

July 19, 2016October 25, 2022
ALLProducts

Finding the location of an underground cable fault just became easier with the VM-510FFL Standalone A-frame locator. Now locating a suspect cable and finding the fault can be done with the VM-510FFL and a compatible transmitter. There is no longer a need for a separate utility locator with cables connecting to it. After...

Cookie Consent